Hydraulic Element Housing
Pentair's Hydraulic Housing is designed for the removal of particulate from oils and industrial fluids. Our housings accept standard element I.D. of 2-5/8" to 3-1/2", O.D. of 6" or 7" and heights up to 36 inches.
Vessel Construction:
Our housing is designed for operating up to 100 PSI at 250 degrees Fahrenheit. The housing design provides a large sump area at the bottom for dirt and scale accumulation with a convenient 2 inch clean-out port. This design utilizes the filter more efficiently and prolongs the element life.
Permanently piped housings are opened with simple tools without disturbing the piping. Swing bolts with eye-nuts allow easy opening and closing of the swing-lid. No need to remove any hardware. As a standard finish, all vessels are blast cleaned and painted inside and out with a 2-part epoxy. Stainless steel vessels are supplied with a satin finish.
Specifications
Housing lid has a 3-bolt swing closure, vent port and Buna o-ring. Connections are 2 inch NPT couplings which may be used in-line or at a 90 degree setting. Housing is supplied with a 2 inch bottom clean-out port for easy maintenance. A two-part epoxy finish is applied on the carbon steel vessels to maximize the life of the housing; stainless steel vessels are supplied with a satin finish. A full tie-rod with aluminum hand nut secures the element for a positive seal. Vessels are rated at a 100 pounds per square inch design.
AVAILABLE ELEMENT SPECIFICATIONS Housing is not supplied with an element.
Size: 6" OD X 2-5/8" ID X 18" HT (single), 36"HT(double)
Media(particulate): Phenolic resin impregnated cellulose
Media(water removal/particulate): Laminated absorbent and resin impregnated cellulose, 3 liters water holding capacity per 18 inch element height
Outer wrap: Electronic tinplate with 3/32 inch openings
End caps: Aluminized Steel
Center core: Heavy duty spiral-locked, corrugated steel rated at 75 PSID
Gaskets: 3/32 inch Buna N
Surface Area 34 square feet per 18 inch element height
Recommended change-out: 15-20 PSID
Flow rate at 100 PSI: 60 g.p.m. at 150 SSU / 1 PSID per 18 inch of element height.
- Carbon or 304 stainless steel construction
- 150 PSI pressure rating
- Low pressure drop
- Quick swing closure with eye nuts
- Buna lid seal
- 2 inch clean-out port
- Full tie-rod element connections for positive seal
- 2 inch in-line connection design
- Vented lid to accelerate evacuation and filling
Vessel Construction:
Our housing is designed for operating up to 100 PSI at 250 degrees Fahrenheit. The housing design provides a large sump area at the bottom for dirt and scale accumulation with a convenient 2 inch clean-out port. This design utilizes the filter more efficiently and prolongs the element life.
Permanently piped housings are opened with simple tools without disturbing the piping. Swing bolts with eye-nuts allow easy opening and closing of the swing-lid. No need to remove any hardware. As a standard finish, all vessels are blast cleaned and painted inside and out with a 2-part epoxy. Stainless steel vessels are supplied with a satin finish.
Specifications
Housing lid has a 3-bolt swing closure, vent port and Buna o-ring. Connections are 2 inch NPT couplings which may be used in-line or at a 90 degree setting. Housing is supplied with a 2 inch bottom clean-out port for easy maintenance. A two-part epoxy finish is applied on the carbon steel vessels to maximize the life of the housing; stainless steel vessels are supplied with a satin finish. A full tie-rod with aluminum hand nut secures the element for a positive seal. Vessels are rated at a 100 pounds per square inch design.
AVAILABLE ELEMENT SPECIFICATIONS Housing is not supplied with an element.
Size: 6" OD X 2-5/8" ID X 18" HT (single), 36"HT(double)
Media(particulate): Phenolic resin impregnated cellulose
Media(water removal/particulate): Laminated absorbent and resin impregnated cellulose, 3 liters water holding capacity per 18 inch element height
Outer wrap: Electronic tinplate with 3/32 inch openings
End caps: Aluminized Steel
Center core: Heavy duty spiral-locked, corrugated steel rated at 75 PSID
Gaskets: 3/32 inch Buna N
Surface Area 34 square feet per 18 inch element height
Recommended change-out: 15-20 PSID
Flow rate at 100 PSI: 60 g.p.m. at 150 SSU / 1 PSID per 18 inch of element height.
Visit the Pentair Catalog for more hydraulic element housing
Contact us for more information on our hydraulic element housing and custom price quote.
